Authors Toni PrahastoDepartement of Mechanical Engineering, Faculty of Engineering, Universitas Diponegoro, Semarang, IndonesiaOjo KurdiDepartement of Mechanical Engineering, Faculty of Engineering, Universitas Diponegoro, Semarang, IndonesiaDwi Basuki WibowoDepartement of Mechanical Engineering, Faculty of Engineering, Universitas Diponegoro, Semarang, IndonesiaAchmad Chairil IsthafatDepartement of Mechanical Engineering, Faculty of Engineering, Universitas Diponegoro, Semarang, Indonesia Abstract The Turbine Cooling Air cooler plays a vital role in maintaining operational reliability in power generation systems by reducing the temperature of compressed bleed air prior to entering the turbine rotor. Cogged V-belt drive was used to be a power transmission in this cooling unit by connecting the electric motor to the cooling fan, where excessive cyclic tensile and bending loads can induce localized fatigue cracking and premature structural failure. This study investigates the internal stress and strain distributions of a cogged Chloroprene Rubber V-belt using a non-linear three-dimensional finite element method in ANSYS Static Structural. A representative volume element submodel with a length of thirty-two millimeters comprising three cogs was constructed to eliminate boundary cut artifacts and ensure numerical convergence. The hyperelastic behavior of Chloroprene Rubber was modeled using a two-parameter Mooney-Rivlin constitutive formulation fitted from uniaxial, biaxial, and planar shear experimental data. Under a displacement-controlled longitudinal extension of fifteen millimeters applied via a remote displacement boundary condition, the simulation yielded a maximum total deformation of 15.217 millimeters. The maximum principal elastic strain reached 0.6922 and was heavily concentrated at the tooth root fillets, particularly on the middle cog, identifying the tooth root as the primary hotspot for fatigue crack initiation. Furthermore, the maximum equivalent von Mises stress and maximum principal stress were recorded at 5.343 megapascals and 5.8328 megapascals, respectively, remaining within safe material limits. These findings provide a targeted visual inspection reference for preventive maintenance of industrial V-belt drives. Keywords Finite Element Method Cogged V-Belt Turbine Cooling Air Cooler Chloroprene Rubber Mooney-Rivlin Model Von Mises Stress Hyperelastic Material Static Structural Analysis Citation of this Article Toni Prahasto, Ojo Kurdi, Dwi Basuki Wibowo, & Achmad Chairil Isthafat. (2026). Finite Element Stress and Strain Analysis of a Cogged Chloroprene Rubber V-Belt in a Turbine Cooling Air Unit. International Current Journal of Engineering and Science (ICJES), 5(11), 19-23. Article DOI: https://doi.org/10.47001/ICJES/2026.511003 Licence Copyright (c) 2026 International Current Journal of Engineering and Science. This work is licensed under a Creative Commons Attribution Non Commercial 4.0 International Licence. References Yang, C., Yin, Q., Xiao, R., Xue, Z., & Ma, X. (2025). Waste-heat utilization for turbine air cooler and fuel heater in gas turbine combined cycle. Applied Thermal Engineering, 277. https://doi.org/10.1016/j.applthermaleng.2025.127061.Amanov et al. (2019). A. Amanov et al., "Experimental Investigation on Friction and Wear Behavior of the Vertical Spindle and V-belt of a Cotton Picker," Materials, vol. 12, no. 5, p. 773, 2019. doi: 10.3390/ma12050773.Yu, Z., Cui, Y., Zhang, Q., Liu, J., & Qin, Y. (2022). Thermo-mechanical coupled analysis of V-belt drive system via absolute nodal coordinate formulation. Mechanism and Machine Theory, 174. https://doi.org/10.1016/j.mechmachtheory.2022.104906.Omorodion et al. (2020) I. Omorodion et al., "Effect of under belting a multiple V-belt drive," Journal of Advances in Science and Engineering, vol. 3, no. 1, 2020. doi: 10.37121/jase.v3i1.72.Mascenik, J., & Coranic, T. (2024). The Influence of Changing Belt Loading Conditions on the Operational Condition of the Belt Transmission. Actuators, 13(12). https://doi.org/10.3390/act13120506.Li, W., & Xin, Z. (2018). Flexural fatigue life prediction of a tooth V-belt made of fiber reinforced rubber. International Journal of Fatigue, 111, 269–277. https://doi.org/10.1016/j.ijfatigue.2018.02.025.Xu, B., Liu, Y., Wang, Y., Ni, X., & Wang, X. (2021). Advanced calculation model of V-belt temperature field. ElektronikaIr Elektrotechnika, 27(3), 4–14. https://doi.org/10.5755/j02.eie.29003.Chen H.Y., Hu X.B., Zhu H.D., et al., 2020, Analysis of internal stress distribution characteristics of conveyor belt, Machine Design, 37, 4, 55-60.Hoover, D., & Kumar, A. V. (2022). Immersed boundary Mindlin-Reissner 3D shell element for modeling isotropic and laminated composite shells. Finite Elements in Analysis and Design, 208. https://doi.org/10.1016/j.finel.2022.103794Liu, J., Zheng, J. yun, Ma, K., Fu, B., Chen, S., & Zhao, Y. (2023). Stress analysis and wear life prediction of metal sheet of CVT under high speed condition. https://doi.org/10.21203/rs.3.rs-1663832/v1.Yao, Q., Dong, P., Zhao, Z., Li, Z., Wei, T., Wu, J., Qiu, J., & Li, W. (2023). Temperature dependent tensile fracture strength model of rubber materials based on Mooney-Rivlin model. Engineering Fracture Mechanics, 292. https://doi.org/10.1016/j.engfracmech.2023.109646.Kim, B., Lee, S. B., Lee, J., Cho, S., Park, H., Yeom, S., & Park, S. H. (2012). A comparison among Neo-Hookean model, Mooney-Rivlin model, and Ogden model for Chloroprene rubber. International Journal of Precision Engineering and Manufacturing, 13(5), 759–764. https://doi.org/10.1007/s12541-012-0099-y